Handkerchief-top Pillow

September 11, 2008 at 2:37 pm (Uncategorized) (, , , , )

Making a Handkerchief Top
A pillow with a bit of a Victorian look can be made from four identical embroidered handkerchiefs. You will need a square of fabric for the pillow back and a top square of that same size that will show as a border around the handkerchiefs. Two rounds of ruffled lace are optional.

Planning Your Pillow
Your pillow can be any size you want. The amount of the top that is covered by the handkerchiefs will depend on the size of the embroidered design on them. Fold the hankies into squares that are a little larger than the embroidery, and place them together in a square with the embroidery at the outside corners. Move them together or farther apart until you like the effect. Determine the size you’ll want each hankie to be, adding seam allowances.

If the edges of the hankies are shaped, making it difficult to use as seam allowances, or if the embroidery is too close to the edges to allow for seams, consider putting the embroidery toward the center instead of the outside corners. The curved edges of the hankies will expose some of the border fabric between them at the center.

You will need the hankies to be connected before they are sewn on the border fabric so you can turn the edges under as one piece or ring the hankies with ruffle. To do this, sew two of the hankies next to each other to a piece of waste fabric from the hankies. Stitch close to the finished edging, but stop before the edgings curve away from each other. Trim the waste fabric so it doesn’t show.

Repeat with each joint.

Advertisements

Permalink Leave a Comment

Making Pillows

September 11, 2008 at 2:36 pm (Uncategorized) (, , , , , , , )

Learning the Basics
Pillows can be made from nearly any fabric. Consider what use the pillow will get when you are choosing between washable and nonwashable fabrics and stuffing. Allow extra seam allowance for fabrics that tend to fray.

Stuffing Material
For best results, use polyester pillow stuffing or ready-made forms. If you want to use a form, purchase it before you cut your pillow fabric, because they are available only in a limited number of sizes. Foam rubber can be cut to order if you can find it available. Cut it about 1” larger than your finished pillow’s dimensions. You’ll want the edges and corners to compress, or your pillow will have a boxy look with empty seams.

Other possibilities for stuffing include shredded foam rubber, which will look fine for decorative pillows but will be uncomfortably lumpy for a pillow for sleeping or sitting on. You can get fair results by recycling women’s hose. Be sure to cut away all elastic and seams, including reinforced toes. Stuff the pillow tightly so the individual hose don’t separate into lumps.

Cut and Stitch
When your pillow is stuffed, it is going to appear smaller than the seam-to-seam measurements. For a pillow to look 12” square, you will need to cut your fabric about 16” by 16”, allowing for ½” seams and about 3” total for thickness. Cut your pillow on the grain of your fabric to assure that it will keep its shape.

If you’ve chosen a stretchy fabric or one with a very loose weave, or if you need to cut your fabric off-grain in order to get the desired effect, make a casing or lining out of muslin or other firm fabric that won’t show through your pillow fabric. Make the casing the same size as your pillow, stuff it, and use it to stuff your pillow once it is together, or use the fabric as lining, stitch the muslin pieces to the back of your pillow fabric pieces, then treat them as one fabric. The back of your pillow can be identical to the front, or it can coordinate. If your front is odd-shaped, pin it to the back fabric—right sides together—and trim the back to fit after they are sewn together.

Stitch ½” from the cut edge all around, leaving a gap of a few inches. If possible, leave your gap in a straight line for easier blind stitching. If you’ve chosen foam rubber or a pillow form, leave nearly all of one side unstitched to make it easier to insert the stuffing Turn and Stuff

Turn your pillow right side out through the gap. Poke out the corners with something blunt and press. Be as accurate as possible when pressing the seam allowance under at the gap so it won’t look different from the rest of the pillow edge.

If you want to have a tiny lip around your pillow, a sort of mock piping, topstitch 1/8 ” from the edge after you’ve turned your pillow all the way around except at the gap. Topstitching is stitching done on the outside that is expected to show. Finish the topstitching after you’ve stuffed the pillow.

Stuff your pillow thoroughly. If you are using bagged stuffing, a wooden spoon can be helpful to get the corners and the rest well packed. Don’t skimp on the stuffing. It will compress a little with use, and you don’t want your pillows getting that floppy, sunken look.

Permalink Leave a Comment